Description
| NOZZLE (Inch) | PLATE THICKNESS (mm) |
|---|---|
| 1/32 | 6 |
| 3/64 | 12 |
| 1/16 | 25,50,75 |
| 5/64 | 100 |
| 3/32 | 150 |
| 1/8 | 250 |
PNM (LPG) Nozzle for NM 250/ NM400
Hard drawn Tellurium copper used in one-piece nozzles
- withstands heat & wear
- out lasts any copper nozzles
One piece nozzle has swaged interior
- Gas passages are mirror smooth with internal angles rounded
- Non-turbulent more efficient gas flow.
- Clean smooth cuts with minimal kerf loss
Preheat ports are closely spaced around cutting orifice
- For greater concentration of preheat flames.
Long parallel preheat passages
- Permit redressing of the nozzle without affecting performance
Related products
-
AGNM (Gouging) Nozzle for NM 400
Hard drawn Tellurium copper used in one-piece nozzles
- withstands heat & wear
- out lasts any copper nozzles
One piece nozzle has swaged interior
- Gas passages are mirror smooth with internal angles rounded
- Non-turbulent more efficient gas flow.
- Clean smooth cuts with minimal kerf loss
Preheat ports are closely spaced around cutting orifice
- For greater concentration of preheat flames.
Long parallel preheat passages
- Permit redressing of the nozzle without affecting performance
-
Heavy Duty Low Power Consumption Welding Power Sources for MIG / MAG Welding
- Heavy-duty Low Power Consumption welding power sources for high quality manual or mechanized MIG/MAG welding output.
- Hex phase rectification gives almost ripple free welding output free from spatter.
- Stick-out control eliminates demand for operator’s skill.
- Fresh Tip Treatment (FTT) control eliminates formation of globules at the wire tip during weld stop condition.
- Fresh Arc Start (FAS) control instantaneously enhances the arc-striking rate for better arc striking.
- Self hold circuitry with crater control module.
- Pre-flow of shielding gas with burn-back control for optimum utilizations.
- An ideal choice for MIG/MAG welding application with enhanced productivity and quality.
-
P-Type (LPG) Nozzle For Cutogen 5
Hard drawn Tellurium copper used in one-piece nozzles
- withstands heat & wear
- out lasts any copper nozzles
One piece nozzle has swaged interior
- Gas passages are mirror smooth with internal angles rounded
- Non-turbulent more efficient gas flow.
- Clean smooth cuts with minimal kerf loss
Preheat ports are closely spaced around cutting orifice
- For greater concentration of preheat flames.
Long parallel preheat passages
- Permit redressing of the nozzle without affecting performance
-
Single Stage Regulator
Conform To: IS 6901-2009 & BSEN ISO 2503-1998
B’ Series single-stage regulators continue the tradition of superior performance in the single-stage range. The latest materials and advanced component design make these regulators suitable to meet the stringent demands of use in shop-floor as well as outdoor conditions with enhanced safety. ESAB 10X-13B and ESAB IDA-4B are the toughest and most reliable units for oxy-fuel gas service. These are provided with two pressure gauges one to indicate outlet pressure & the other to inlet pressure. Also available are ‘C’ series single-stage regulators with only one gauge to show the cylinder pressure. The working pressure calibrated on the bonnet can be set by the pressure adjusting knob. A low-pressure LPG regulator suitable for Oxy-LPG cutting, Air-LPG equipment, and healing applications is also available. The outlet adjustable pressure is 0-1 kg/cm2.
Imported Safety Pressure Gauges Designed For 300 bar services pressure , confirming to ISO 5171 standards.
Reviews
There are no reviews yet.